Marvin Panday

Testing and inspecting electrical components, assemblies, and systems to ensure compliance with engineering plans and specifications.

• Built prototypes of new products according to design specifications.
• Evaluated schematic diagrams prior to beginning any installation project.
• Improved electrical installations by standardizing procedures for production and field personnel.
• Determined appropriate cables, fuses and electrical elements to use during installation phase of weapons detection systems.
• Wiring the Power, Control and Metering circuit as per Engineering designed like PLC, Protection Panel, MCC, and other control panel.
• Assemble Form 1 to Form 4 Partitions type Tested Switchboard and Panelboard.
• Fabricate busbars and other metal support and can operate other fabrication machine such as Bender Machine, Cutting Machine and other fabrication equipment.
• Have ability to assemble B&R Enclosure, Rittal, NHP, Schneider Prisma and more.
• Can performed to comply some switchboard works as per Australian standard.

• Electrical works in Industrial and commercial wiring such as Building Monitoring Systems, power circuits, and lighting circuits.
• Assembling of the Panelboard, Distribution Board, and Switchgear re-built in.
• Assembling, lay-outing, fabricating of cable management.
• Wiring of low voltage and low current systems.
• Wiring in switchgear, MDB (Main Distribution Board), ATS (Automatic Transfer Switch).
• Cable pulling.
• Switchgear cable termination using armored cable up o 240 mm squared.
• Testing of functional test, RCD Test, Earth loop impedance, Prospective Short Circuit Current Test.

• System integrator, Instrumentation, Automation, Control Panel distributor, and Traffic lights, with an authorized dealer and distributor product of Parker, Invertek, Fatek, Siemens, etc.
• Assembling of Control panel, Motor control center. Traffic Control system.
• Lay-outing of the control panel, PLC, Traffic light panels, AC Drives, DC Drives, and Soft-starter.
• Wiring of control, power, metering circuits, and devices.
• Assembling of Mimic board, Data cabinets for system integration.
• Busbar fabrication.
• Preventive maintenance of AC and DC Drives.
• PLC programming.
• Fabrication of metal supports for panel boards.
• Testing and commissioning.

• Manufacturing of Switchgears, Switchboard, And any type of Electrical Panelboards such as MVSG, LVSG, ATS, MCC, PLC panel, etc. All product line is Schneider. Authorized dealer, partnership, and distributor of Schneider Electric.
• Box assembling type tested panel, any type of IP panel.
• Lay-outing of all types of electrical components for switchgear, control panels, motor control center, PLC, DCS, SCADA.
• Wiring of controls, power, metering circuits, and any protective devices. Including dressing of cable from point to point and addressable wire tagging.
• Assembling of metal works and fabrication for supports, panel bases, and bracketing.
• Assembling of busbar in MCC, Switchgear, Distribution board, etc.
• Conducting functional testing, sequences testing, re-tightening, and torque marking of bolts and nuts.
• On-site panel Assembling with Final testing and commissioning.
• Servicing with assembling, troubleshooting, and retrofitting.

• Manufacturing of Switchgears, Switchboard, And any type of Electrical Panelboards such as HVSG, MVSG, LVSG, ATS, MCC, PLC panel, etc. All product line is Mitsubishi. Authorized dealer and distributor of Mitsubishi Electric Japan.
• Checking/reading electrical drawings from Engineering Dept. Studying for some electrical sequences, controls, devices/components, and proper specific rated voltage.
• Components preparation for lay-outing in mounting plates. Box assembling doors and hinges, base support, Lifting eye bolt, and other accessories.
• Lay-outing of any components to mounting plates like Terminal blocks, Din Rails, Auxillary relays, Magnetic Contactor, Timers, PLC, Over Current Relays, Current Transformers, Potential Transformers, etc. Including drilling and threads hand tapping for cable trays, busbars, screws, and bolts. And any metal fabrication needs for support and bracketing inside the panel or switchgear as per engineering design.
• Start of wiring for controls, power, and metering circuits of all components and some type of protective relays Over Current Relays, Under Over Voltage Relays, Air CB, Vacuum CB, Gas CB, Current Terminal Test, Power Terminal Test, Any types of Current Transformer. AC Drives.
• Fabricate busbar supports. Fabricate busbar for those needed with re tightening and torque marking.
• Conduct testing with an acceptance test, Testing the sequences/operation controls with assistant and witnesses of engineer based on safety and standard procedures.
• Site testing and commissioning, Like set the parameter settings and fine tuning.
• Substation maintenance of the following equipment such as Power Capacitors Reactors, Load break Switch, Low Voltage Circuit Breaker, and Vacuum Circuit breaker.
• Troubleshooting, Modification of controls, retrofitting, and energisation.

• Wiring of power and control of machinery equipment and building facility with testing and commissioning.
• Troubleshooting and modification of electrical existing wiring as per engineering and design department.
• Monitoring of some different electrical meters and protective devices (analog and digital).
• Metal fabrication and other metal work.
• Preventive and corrective maintenance of Switchgear and other electrical panel board.